SERVICE
Contact Us
Service Concept
SERVICE CATALOG
Service concept of "with heart and satisfaction"
Keep an eye on every customer
Scientific service system
FAQ
How does the range hood work?
According to the basic principles of fluid mechanics, the motor drives the wind wheel to rotate. In the air inlet and air cabinet, the air outlet generates a negative pressure, and the pressure difference between the air outlet, the air cabinet and the air outlet is realized, which leads to the suction and discharge of air. The oil fume is sucked and discharged due to the pressure difference. When the oil fume passes through the air inlet filter screen, part of the oil fume is cooled and separated, and the cooled and condensed slop is introduced into the oil cup and discharged from the body along the oil guide system, while the rest of the slop is discharged It will be produced by agglomeration in the internal cavity of the machine, and will be discharged from the machine body along the oil guiding system, and the fumes after oil fume separation will be discharged from the air outlet.
What is the basic working principle of the stove?
The basic working principle can be divided into ignition phase, primary mixed combustion, ignition phase and combustion phase. Ignition stage: Open the valve during ignition, the gas enters through the pipeline with a certain pressure and is ejected from the nozzle; primary mixed combustion: due to the ejection effect of the kinetic energy of the gas, the gas ejected from the nozzle draws in the primary air from the air door and is in the ejector. The ignition phase of the mixed gas is completed inside: the mixed gas flows out through the fire hole of the burner and starts to ignite when it encounters the fire source generated by the igniter; the combustion process: after ignition, the gas obtains secondary air supplement from the burner and completes the complete combustion.
Disinfection cabinet news answer
How the product works
Disinfection of tableware is a process of using physical or chemical methods to kill pathogenic microorganisms in cleaned tableware. In terms of function, disinfection cabinets on the market usually have three disinfection methods: high temperature disinfection, ozone disinfection and ultraviolet disinfection, as well as the combined disinfection methods between them. The following is a brief description of its working principle.
Electric tableware disinfection cabinet
The electric heating disinfection cabinet for tableware is a disinfection cabinet which is heated by electric heating elements to disinfect the tableware. The high temperature disinfection cabinet is the most common electric heating disinfection cabinet on the market. It uses high temperature to play a bactericidal effect. In the high temperature and dry air, it has an obvious lethal effect on bacteria. The protein in bacteria and viruses is denatured and solidified due to heat, the activity disappears, and the metabolism is blocked, leading to death. Usually, milky white quartz heating tube is used for heating. In the form of far-infrared direct radiation and air convection, the items and air in the cabinet are heated to above the set temperature, and the high temperature must be maintained for longer than the specified time.
In order to reach the set disinfection temperature and time, the high-temperature disinfection cabinet adopts a thermostat or a microcomputer program to control the working time of the disinfection cabinet, and the power is automatically cut off when the work is completed.
Ozone disinfection cabinet
The electric heating disinfection cabinet for tableware is a disinfection cabinet which is heated by electric heating elements to disinfect the tableware. The high temperature disinfection cabinet is the most common electric heating disinfection cabinet on the market. It uses high temperature to play a bactericidal effect. In the high temperature and dry air, it has an obvious lethal effect on bacteria. The protein in bacteria and viruses is denatured and solidified due to heat, the activity disappears, and the metabolism is blocked, leading to death. Usually, milky white quartz heating tube is used for heating. In the form of far-infrared direct radiation and air convection, the items and air in the cabinet are heated to above the set temperature, and the high temperature must be maintained for longer than the specified time.
In order to reach the set disinfection temperature and time, the high-temperature disinfection cabinet adopts a thermostat or a microcomputer program to control the working time of the disinfection cabinet, and the power is automatically cut off when the work is completed.
UV disinfection cabinet
The principle of ultraviolet sterilization is to use ultraviolet light with a central wavelength of 253.7nm from an ultraviolet lamp to directly irradiate bacteria, viruses and microorganisms with a certain irradiation intensity and irradiation time to destroy their tissues and die. The penetration ability of ultraviolet light is very weak, and the backlight part of the object cannot be disinfected. Therefore, the national standard clearly stipulates that the disinfection cabinet that only depends on ultraviolet disinfection cannot be used for disinfection of tableware. The high-ozone ultraviolet lamp made of special quartz glass produces sterilized 253.7nm ultraviolet rays while also producing 184.9nm ultraviolet rays at the center wavelength. The 184.9nm ultraviolet rays can synthesize oxygen molecules in the air into ozone molecules. Therefore, the high-ozone ultraviolet lamp can be used as the disinfection source of the tableware disinfection cabinet. Ultraviolet rays + ozone + medium temperature is the most popular disinfection method for UV tableware disinfection cabinets on the market.
Ultraviolet rays have a strong irritation to human skin and cornea. Looking directly at the UV lamp for a few minutes can cause eye pain, redness and swelling. Quartz glass can pass ultraviolet rays well, while ordinary glass is basically opaque. Therefore, the ultraviolet disinfection cabinet must be equipped with a door switch to prevent human radiation damage from ultraviolet rays.
Common fault repair principle
Fault name |
Failure phenomenon |
Cause Analysis |
Troubleshooting method |
The whole machine does not work, leakage |
The whole machine does not work |
No electricity or poor contact in the power socket |
Use a multimeter to check if there is electricity or change the socket |
Blown fuse |
Replace the fuse of the same specification |
||
Poor contact or open circuit between the power cord and the circuit board |
Check whether the power cord socket is connected to the circuit board and repair it | ||
Circuit board failure |
Replace the circuit board |
||
Automatic alarm |
The door switch is not closed |
Adjust the baffle of the door control part or replace the door control switch |
|
Leakage |
The support leg of the circuit board is broken and touches the shell |
Reinstall the bracket or separate with insulating material |
|
There are foreign objects around the circuit board and switch display that are connected to the shell |
Clean up foreign objects around the circuit board and switch display |
||
The wire insulation layer is aging, damaged and touches the shell |
Replace wire or repair |
||
Poor drying and high temperature effect |
Poor drying and high temperature effect |
Too much tableware is stacked in the cabinet, too dense |
Adjust the number and spacing |
The cabinet door is not closed tightly, and the door seal is deformed and heat overflows |
Adjust the fixing screw of the door hinge seat or replace the door seal |
||
One of the quartz heating tubes burned out |
Replace the quartz tube |
||
The conductive column of the heating tube is loose and the contact is poor |
Re-tighten |
||
The temperature limit of the thermostat is too low |
Replace the thermostat |
||
The resistance wire of the heating tube becomes thinner, the resistance increases and the power decreases |
Observe the brightness of the heat and the color of the heat pipe after the power is off and replace it |
|
Failure phenomenon |
Cause Analysis |
Troubleshooting method |
UV lamp does not work |
UV lamp does not work |
Transport is too savage,Cause the lamp tube contact and the lamp holder contact to shift. |
Just turn the UV lamp |
Check whether the connecting wire is off or broken, causing the whole circuit to be blocked |
After the entire line is transmitted, check whether the entire circuit is unblocked with a multimeter, and pay special attention to whether the UV lamp socket is in poor contact | ||
Check if the rectifier has voltage output |
Replace the electronic ballast of the same specification |
||
Visually check whether the tungsten filament of the UV lamp is disconnected |
Replace the lamp with the same specification |
||
Ozone does not produce | Ozone does not produce | Check whether the cabinet door is closed well, and confirm whether it is caused by the door control switch not being closed | Close the cabinet door or adjust the cabinet door, or press it by hand to confirm whether it is effective |
Whether the gate control switch is on and off normally, judge whether the gate control switch is in bad contact | Use a multimeter to check whether the contact performance of the door control switch meets the requirements | ||
Check whether the connecting wire is off or broken, causing the whole circuit to be blocked | After the entire line is transmitted, use a multimeter to check whether the entire loop is unblocked | ||
The power supply of the ozone generator is abnormal |
Use a multimeter to measure whether there is voltage output at the output of the ozone generator on the main control circuit board, and the circuit board is not replaced. |
||
No ozone | Replace electronic ballast | ||
The tableware is yellow or there is peculiar smell or mold in the cabinet | Tableware turns yellow | The tableware is dirty, and the inside of the cabinet with organic storage is dirty |
Keep the tableware clean and the cabinet clean |
The temperature limit of the disinfection thermostat is too high |
Replace the thermostat with the same specification |
||
Smell | The cabinet door was opened before the ozone was decomposed |
The door can only be opened after 20 minutes of power failure |
|
Get mouldy | The tableware was placed in the disinfection cabinet and the disinfection program was not started in time |
Communicate with customers and start the disinfection program in time |
Precautions for daily maintenance and use of disinfection cabinet
} Precautions for daily cleaning and maintenance
1、The power plug must be unplugged when cleaning the disinfection cabinet;
2、Wipe the inner and outer surfaces of the cabinet with a warm and damp cloth, wipe with a neutral detergent, and then wipe with a clean cloth;
3、Avoid cleaning with hot water, gasoline, alcohol, washing powder, and alkaline detergent. It is strictly forbidden to spray the cabinet with water directly to prevent the electrical insulation performance from degrading and causing danger.
4、It is strictly forbidden to directly splash water and spray the inner and outer boxes to avoid the risk of electric shock due to poor circuit insulation
} Precautions for daily use
1、The power socket of the disinfection cabinet must be installed with a reliable grounding wire, and the socket of the specified specification shall be used. The user shall not modify the plug without authorization, and it is strictly forbidden to operate without grounding;
2、When the high temperature disinfection function is selected, it is only suitable for the disinfection of glass, ceramic, stainless steel and other tableware with a temperature of 170℃ or higher (except for the sealed cavity). It is forbidden to put low-temperature-resistant wooden and plastic tableware into a high-temperature box for disinfection, so as to avoid the danger of deformation, damage or burning, and not to put non-tableware (such as clothing, towels, shoes and hats, etc.) into the disinfection cabinet. Tableware whose temperature resistance is lower than 70℃ shall not be put into the disinfection cabinet;
3、Pour the water on the tableware to achieve a good disinfection effect. Too much water will cause circuit failure. The oil on the tableware should be thoroughly cleaned, otherwise the oil will cause peculiar smell in the cabinet, and there should be left between the tableware. In the gap, the tableware is crowded together, which will affect the disinfection effect;
4、After the cabinet door is closed, the disinfection cabinet can work normally. Please do not open the cabinet door during the disinfection process, otherwise it will affect the disinfection effect, prolong the disinfection time, and may even cause ozone leakage or ultraviolet radiation; the tableware should be washed and drained Then put it into the disinfection cupboard for disinfection, which can shorten the disinfection time and reduce the power consumption.
5、Hands and utensils should not touch the radiant panel to avoid being scalded and damaging the parts.
6、If a large amount of ozone leakage is found during use or the light emitted by the ultraviolet lamp can be directly seen without passing through any light-transmitting objects, you should stop using it immediately, unplug the power plug, and notify the authorized maintenance outlet to perform repairs. Do not repair by yourself;
7、After disinfection, the effect will be better if you take it out after 10 minutes. A small amount of ozone odor overflows when the cabinet door is opened. This concentration is not harmful to human health, please rest assured.
Service Hotline:
400-930-0138
Address: Wentian Industrial Zone, Dongsheng Town, Zhongshan City, Guangdong Province
Join Hotline:18676416899(Manager Deng)
FAX:0760-22222707
E-mail: zschuzhibao@163.com
Copyright©Zhongshan Kitchen Utensils Treasure Electronics Co., Ltd
粤ICP备2021098952号 Powered by www.300.cn
Zhongshan Kitchen Utensils Treasure Electronics Co., Ltd. Reserves the right of final interpretation of any content displayed on this website